Ceramium® consists of two components and offers maximum resistance to wear and material loss from metal surfaces.

Description and application
Due to a very hard protective layer, Ceramium® provides optimum protection against corrosion, erosion, wear and cavitation in dry and wet conditions. Ceramium® is available as a paste and in liquid form.

Ceramium® CH is a wear-resistant polymer-ceramic with very good chemical resistance.

Description and application
This product is available with different hardeners, depending on the application.

• Application of hardener CH1: Inorganic (mineral) acid, even in concentrated form. Base/lye/alkali and oxidising salt solutions.
• Application of hardener CH2: Aromatic and halogenated hydrocarbons, ester, ketone, alcohol and organic acids, even in high concentrations.

A chemical resistance list is available from EMHA.

MM-Elastomer is a material with ‘rubber-like’ properties. These urethane-elastomer systems offer a very good combination of flexibility, strength and chemical resistance.

Description and application
MM-Elastomer can be used to make elastic joints or to repair components. One of the big advantages of this product is that there is no need for primer before application. The product offers good resistance to high temperatures and excellent adhesion to metal surfaces.

Hardnesses
MM-Elastomer always consists of two components. Depending on the application, a paste, liquid or brushable variant can be chosen in the following Shore A hardnesses:

• 95: standard with the best technical properties and chemical resistance
• 85: for production and repair of electrical components
• 65: for production and repair of electrical components and coatings
• 40: for production of electrical components and coatings

MM-metal oL-steelceramic is a two-component polymer metal, tested and certified for the repair of metals and alloys contaminated with oil, grease or fuel. MM-metal oL-steelceramic is used to repair damage caused by corrosion, chemical attack, abrasion, cracking or impact. 

Description and application
What makes MM-metal oL-steelceramic so unusual is that it provides both extremely good adhesion to oil-contaminated metal surfaces and high resistance to chemicals. Depending on the application, you can choose either a red or yellow hardener:

• The yellow hardener offers the best technical properties.
• The red hardener is suitable for emergency repairs because it cures very quickly.

MM-metal oL-steelceramic is certified by Lloyds Register of Shipping.

MM-metal SS-aluminium is a two-component, aluminium alloy-based polymer metal suitable for a wide variety of repairs of aluminium components.

Description and application
The alloyed aluminium in the polymers makes this material particularly suitable for aluminium repairs. This makes it possible to reliably repair damage to aluminium parts caused by corrosion, strain and chemical attack. MM-metal SS-aluminium is available as a paste and in liquid form. The paste variant retains its shape during application, while the liquid variant can be injected, poured or applied with a brush.

MM-metal SS-bronze is a polymer metal based on an alloy of copper and tin, making it very suitable for the most diverse repairs of bronze components. This makes it possible to reliably repair damage to bronze parts caused by corrosion, strain and chemical attack.

Description and application
MM-metal SS-bronze consists of two components and is available as a paste and in liquid form. The paste variant retains its shape during application, while the liquid variant can be injected, poured or applied with a brush.

MM-metal SS-steel is a two-component, metal alloy-based polymer metal suitable for a wide variety of repairs of steel and iron materials.

Description and application
The alloyed metal in the polymers gives them the same properties as metal, so lost material can be filled in. This makes it possible to reliably repair damage caused by corrosion, wear, cracks or impact. MM-metal SS-steel is available as a paste and in liquid form. The paste variant retains its shape during application, while the liquid variant can be injected, poured or applied with a brush.

MM-metal SS-steel 382 is a two-component polymer metal, suitable for repair and as a construction material, that can be used to optimise the technical properties of metal.

Description and application
MM-metal SS-steel 382 provides the best technical properties under mechanical load. The product is available as a paste and in liquid form. The liquid variant is very pourable due to its high surface tension. This variant can even be injected through very small openings (from 2 mm).

MM-metal SS-steelceramic is a two-component polymer metal suitable for the most diverse repairs of metals and alloys.

Description and application
This product is often used for repairing parts that are under water, or for repairing leaks (even under pressure: tested at 80 bar pressure for a long period).

The product can be applied at temperatures above 0 °C. Two hardeners are available for MM-metal UW, which differ in processing time:

• Hardener UW3 is suitable for quick sealing of leaks
• Hardener UW9 is suitable for applications in hard-to-reach areas or at high ambient temperatures.

MM-metal UW is certified by Lloyds Register of Shipping.

MM-metal SS-steelceramic is a two-component polymer metal suitable for the most diverse repairs of metals and alloys. With MM-metal SS-steelceramic, damage caused by corrosion, chemical attack, wear, cracks or impact can be repaired very reliably.

Description and application
MM-metal SS-steelceramic is characterised by its exceptional technical properties, extremely good adhesion to metal surfaces, higher abrasion resistance and high resistance to chemicals. Depending on the application, you can choose either a red or yellow hardener:

• The yellow hardener offers the best technical properties.
• The red hardener is suitable for emergency repairs because it cures very quickly.

VP 10-500 is an organic-based polymer metal, suitable for repair and maintenance of metals at high temperatures.

Description and application
VP-10-500 can be applied to both cold and hot metal parts. The material will not harden at room temperature: hardening starts at a metal temperature of at least 75 °C. As a result, its resistance to high temperatures is much higher than that of standard polymer materials. It also has a high chemical resistance, especially to sulphuric acid.